- Listed: April 3, 2019 12:48 am
These simple and easy steps will help you measure your countertops. Make sure you include the island if there is one and what type of sink you have as well. The backsplash measurement is important but needs to be measured separately. Using the box method, start at the wall and measure to the counter edge. Make sure to measure each counter section individually and as accurately as possible.For a full backsplash, measure the height from where the counter starts to the underside of the cabinets.
Also consider if the seating area overhang is connected to the countertop as a second level. If the island is curved, find the center of the curve and form a square in your drawing. Multiply the length by the width for each piece and then add together to get the total inches. Make sure you double check your measurements and calculations. Working together will insure the best outcome at the best price for your remodel.Taking your own measurements before you go shopping will aid you in getting an appropriate quote. Once you have the basic layout, create appropriate sections for measurement by boxing out sections and numbering them. Always start from the wall and measure to the edge of your countertop. For a standard 4″ backsplash, measure this from corner to corner as well. It is measured basically in the same way as the previous measurements; but adjustments must be made for seating area overhang. In this case it is important to not only measure both levels of the countertop but also the height of the second level from the first countertop. Then measure length and width in the same way as previously. To get the most accurate final estimate it is important to make your measurements as precise as possible. Remember, your sketch does not have to be perfect and the company will obtain measurements as well.
How A Granite Countertop Is Measured Cut and Installed • DIY Projects by ronhazelton.com
This should be the most peaceful of all the areas of the house.
A few days later, a technician arrives at her home, to make a template. Like most laminate countertops, this is held down with a few screws. But only about 3 for the whole countertop, so it seems like this is also glued on here. Finally the last of the old countertop makes it’s departure. Once the slab is in place, it takes a team of skilled craftsmen to do the final trimming and fitting. Be sure to visit the slab yard to view a larger piece of the chosen granite as a more representative sample before selecting the granite for your kitchen countertop. It turns out that she was planning to install a new granite countertop, now granite’s never seemed very energetic to me, it sort of just lies there.
You up for a little sort of like a shopping trip?
Wonder what these uh, what these, the price range is on these. The template is made by laying thin strips of glue on plywood along the edges of the existing countertop. The individual strips are then glued together with a hot metal adhesive, forming a rigid pattern, that can be lifted off in one piece. The saw is equipped with a diamond blade that’s water cooled to prevent the granite from chipping or cracking. Well the stone cutters have done their job, but the new countertop can’t go in, until the old one comes out.
So we’re gonna kind of do the same thing that we just did, so if you want to grab your putty knife again. The dishwasher is coming out too, so we can reach the screws that are holding down this section of the countertop. The new sink will mount underneath the new countertop, and is clamped in place until it can be permanently attached. Learn how granite countertops are installed; includes details on templating granite fabrication as well as its installation.
Should You Hire A Professional Or DIY A Quartz Countertop Installation? by countertopguides.com
The piece will be extremely heavy, though not particularly fragile. The cabinet must be extremely sturdy and prepared to receive the weight. Ideally the countertop will be the precise shape and size that you want, but if you do need to cut it down you will need a wet saw. Because the quartz is set in resinous matrix you must use caution when polishing; if it gets to hot it may melt or char. Quartz countertops might be reasonable subjects for a do it yourself project under certain conditions. Using pre-purchased slabs will work only if they are the right size and shape, because most diy handymen do not own the tools to cut or polish resinous quartz.
Laser Measure Countertop Demonstration | Duration 2 Minutes 32 Seconds
If you do not have a dependable group of competent and experienced lifters ready to help you move the slab into position we recommend that you use a countertop construction specialist, who can help you much more safely and economically. The two most important things in a quartz counter install are to prepare the cabinet beneath it and to get the counter to the cabinet. Reinforcement and solid wood construction are strongly recommended. Silicone sealing can be less important than usual because the weight of the counter will hold the sink in place with an airtight seal.
You should possess the tools to measure the area perfectly and have a budget generous enough to pay for a precisely fabricated slab. The extreme weight of the quartz countertop should also be considered, with larger pieces weighing more than three hundred pounds.
How To Replace Countertops With Pictures by m.wikihow.com
Then, secure them to the wooden supports and fit the sink and range to make your countertops the best part of the room.
Countertop Installation Service From The Home Depot From Homedepot | Duration 1 Minutes 26 Seconds
First, turn off the lines by finding the shutoff valves under the sink and range or by turning off the main valve in the basement. Place a bucket under the pipes to catch any water left in them. Use a screwdriver to loosen these, then slice the caulk around the top of the sink or range with a utility knife. Make sure the unit is off to the unit if you’re removing an electric range. Stubborn countertops, particularly older ones installed incorrectly, need to be pried off the countertops with a pry bar. Then you can use a larger pry bar to lift the entire countertop. To avoid damaging the countertops, be careful and work as slowly as possible. Many marble or granite countertops are only put on with adhesives rather than screwed in. Run a tape measure along the space where the countertop will rest. Put on safety goggles and a dust mask first to protect yourself from flying shards and material particles. Placing masking tape over the cutting lines can reduce splintering.Flip the sink or range over, then use a pencil to trace around their perimeter.
Your sink or range may have come with a template to be used when sketching the outline. The trace lines can be hard to see against dark countertops. Cut all the way around the outline and clear away the excess material. Be sure to get the inside of the countertop where you cut the space for the sink or range. If they’re not high enough, the front will overhang and block the cabinet doors.Some countertops come packaged with these strips, so you won’t have to make them yourself. Start at one end of the cabinet structure where the countertop will rest. Its ends should rest on the front and back edges of the cabinet. Drill a hole in both ends of the strips, directly over the cabinet frame. Turn the screws with a cordless screwdriver to secure the strips in place. Lay them on top of the build-ups and ensure they connect smoothly. Make any adjustments you need by reducing the size of the build-up strips or the countertops themselves. Pre-cut countertops should come with miter bolts to fasten the countertop pieces together. If you cut the countertops yourself, make miter joints first to fit the countertops together. Another way to connect countertop pieces is to get an aluminum joining strip from the store. Slide the other countertop piece into the joining strip’s groove. Make sure the countertops are securely bolted together first. Lay the tool flat against the wall and adjust the pencil end so the tip is on the edge of the tape.The countertop should be as level and close to the wall as possible. Apply a bead of silicone caulk along the miter joints on the countertop edges. When using aluminum strips instead of miter joints, you won’t need to do this, so enjoy skipping the extra work. The easiest way to do this is to drill up through the build-up strips. For extra support, place small angle brackets along the build-up strips. Double-check the thickness of your countertop and build-up strips and get longer or shorter screws as needed.
You can then measure that far down from the tip of your drill bit and place a piece of tape there to show you when to stop. Finish sealing the countertop by securing the backsplash to the wall. Spread a bead of the caulk all around the edge of the sink or range. Brush a layer of contact cement over the backs of the side strips. Press the strips to the countertop’s edges to hold them in place. Next, cut your new countertops to the correct size, set the countertops down, and cut out the shapes of the appliances. Then, sand the countertop down to the scribe line, caulk the miter joints, and screw the countertops to the cabinets. Fortunately, replacing laminate countertops is a project that you can tackle on your own. Use pliers to twist the ring-shaped nuts to remove the drain pipe and p-trap. If you have a garbage disposal unit attached to your sink, don’t forget to unplug the cord from the outlet. Look underneath the sink or range to find screwed clamps securing these features to the countertops. Once finished, push the sink or range from the bottom to lift it off the countertop. Disconnect the power wires in the metal box behind the range to pull the range out.
Pro Countertop And Carpenter Tape Measure | Duration 1 Minutes 4 Seconds
If your countertop has a backsplash secured to the wall, it’ll also have caulking. Run the tip through the caulking all the way to the other end of the backsplash. Remove the drawers and cabinet doors and look at the underside of your countertop. Undo these screws to free the countertop and move it from the wooden supports.
You may also slip a reciprocal saw between the countertop and cabinets to cut screws and nails. Avoid cutting into the countertop from above when using a saw. If you have your old countertops on hand, they may serve as a useful guide. When building around a corner in your room, plan on connecting 2 countertops cut diagonally. For synthetic countertops like laminate, use a fine-tooth handsaw or jigsaw to fashion the countertops.
You may still need to make some cuts to fit the countertops once you have them.
You may want to set the countertop in place first to get a better idea of where these features need to go. If it doesn’t, use posterboard or cardboard to trace your own sink or range template. Place masking tape first and trace over it to make the lines more visible. Drill holes large enough to fit your saw blade in each corner of your countertop. When the edges feel smooth and safe to the touch, you’re ready to move on. Place the countertops on the wooden supports or measure their front edges. In particular, pay attention to where 2 pieces of countertop meet. Place the miter bolts in the miter joins on the undersides of the countertops, then twist the end of the bolt to secure everything in place. These can be tricky to make, so consider hiring a professional. Cut it to size, then screw it to the side of the countertop. Push them all the way back and gauge how much of a gap remains between the countertop and wall. Get a scribing tool, and find the largest gap between the countertop and wall. Keep the scribing tool at this length and draw the line all the way across the tape.
You may need to add shims under the counter or scribe and sand the cabinet’s sides to do this. Wear down the back part of the counter to the line you traced. Push them against the wall and measure them again with the scribing tool.Then push the countertops together and secure the bolt in place one last time. Apply the screws so they enter but don’t exit the countertop. Screw the brackets into the countertop and the cabinets to hold them in place. To prevent any damage to the countertops, measure the countertop depth first. Squeeze a bead of caulk into the gap and move the caulk gun all the way across the backsplash in one motion. Silicone latex caulk is the best choice since it’s both water-resistant and paintable. Flip these objects over and find your tube of silicone caulk. When finished, carefully pick up the object and lay it into the hole you cut earlier. If they haven’t been pre-cut, measure the length of the free edges of the countertops. Wait about 20 minutes for the glue to feel dry to the touch. It helps to place a towel over the countertop to avoid getting the glue on it. Before you begin, place a towel over the countertop to avoid damaging it. Take your time getting the strips to blend in so you avoid scratching your new countertop. After that, bolt the countertop pieces together, slide them against the wall, and scribe the backsplash.
Granite Countertop Measurements and Templates by doityourself.com
However, handy homeowners can save money by measuring and installing the granite themselves. However, fabrication sometimes requires full-size templates. When measuring your kitchen, start at the wall and work your way to the end of the counter or the opposite wall. When working with bare cabinets, measure from the wall to the end of the cabinet. The fabricator will help you determine the correct overhang measurement. Indicate where the finished edges, backsplashes, and appliances will go. If you’re unsure of the sink’s center, measure to the point where the cabinet doors meet in the middle. Then, from underneath, trace the outline of your cabinet or counter. This is an important step: if this isn’t clear, you may end up with a mirror image of your actual counter!
If you traced bare cabinets, indicate where the overhang will be and how much overhang you would like. Always inspect the finished product when you pick it up or receive it. Many granite countertop shops offer in-home measurements and installation. For these installations, your fabricator will ask for the measurements of your counters. If your kitchen is made of 90-degree cabinet sections, templates are usually unnecessary. If your existing counters are still in place, remember to adjust for the thickness of your backsplashes.
You should also measure from the wall to the center of your sink.Professional template-makers use thin strips of plastic to outline the area. Mark the top so that the fabricator will know which way is up. If you traced your existing counter, mark the template as such. Clearly mark the finished edges, the locations of any adjacent appliances, and the backsplash areas. Would someone who has never seen your kitchen be able to figure out what it looks like?
Corner Bracket by federalbrace.com
Reinforcement on corner countertop overhangs needed to be addressed. They obviously can not be longer than your overhang, and cannot leave more than four inches of unsupported countertop.
We created a useful tool to help you select the proper supports. Select a countertop support that will fit under the overhang. But what about the lengthy corner protrusion when two adjacent overhangs about?
Selecting a countertop support for a corner overhang is a little more complicated, especially if the overhangs have different depths. Use this value to determine the overhang depth outward from the island corner to the edge of the countertop overhang (or corner if both overhang depths are the same). If your overhang size is not listed, then the bracket is too large or too small for this application.
Digital Laser Countertop Template For The Kuppersmith Project House by todayshomeowner.com
The template was then used to cut and shape each of the countertops for the kitchen to the exact size needed. Buyer beware – laser systems used for digital templating are very cumbersome, time consuming and less accurate compared with other countertop digital templating systems. Rather than constructing a template from wood, plywood, or cardboard; a special laser measuring device was used to record the dimensions needed for each of the countertops, as well as the size and locations of sinks and cooktops. A digital template was created by the computer and e-mailed to the fabrication shop.
Excellent Laser Countertop Measuring Tools Wk_62 by progressivemultifocalleukoencephalopathy.org
Naturally, that features the access of your company templates.
It’s the between replicating and pasting some text, or retyping it.
ITM Integrated Tool Management Systems For Stone CNC Routers by parkindustries.com
You can do a single tool, a complete set or the whole tool rack , it’s up to you. There’s no probe to break or constant operator intervention needed. Tools are spun at 1, 000 rpm for scanning to ensure accurate high-point measurements. Operators are prompted to acknowledge scan results for each tool. The color system helps operators understand tooling wear so that they can react quickly to avoid excessive wear on other tools as well as compromised edge quality. Get consistently better stone finishes and peace-of-mind production performance knowing you’ve always got optimized diamond contact on your material. The operator uses a touchscreen interface to indicate which tools to check and then presses cycle start. The laser is mounted on the tool rack out of the way of production activities and protected from contamination with positive air pressure. Special mathematic algorithms determine the best locations to measure different tool types (encapsulated, non-encapsulated).
- Source – granitemarblewa.com
- Woodworking Workshop – ronhazelton.com
- Creative Surfaces Inc Countertops Sioux Falls SD – creativesurfaces.com
- Source – countertopguides.com
- Titled Replace Countertops Step – m.wikihow.com
- Granite Marble Speciies – m.youtube.com
- Source – doityourself.com
- Source – rustoleum.com
- ANTEM HIDDEN CORNER BRACKET AND ASBURY DESIGNER CORNER BRACKET – federalbrace.com
- Atlas Offline Stone CNC Profile Tool Measurement and Management Solutions Png – parkindustries.com
- Kuppersmith Kitchen Renovation Begins – todayshomeowner.com
- Excellent Laser Countertop Measuring Tools Wk – progressivemultifocalleukoencephalopathy.org
- Integrated Tool Management ITM System For Automated Tool Monitoring On TITAN CNC – parkindustries.com
- Videos – Countertop Measurement Tool | By Prodim International, SeigleCabinetsCenter, Prodim International, Granite & Marble Specialties, Expressions-LTD, Marble com TVChannel
13 total views, 1 today
Listing ID: N/A